Discussion:
Re: FTP
(too old to reply)
louis@xtsoft.com [hercules-390]
2018-05-19 01:51:03 UTC
Permalink
Hi
Brian I thank you for the time you spent on my problem.
you are right E22-E23 are not defined in my IODF.


I tried to define them and I got problem.


In the IODF of the Z/OS working well I can see
chpid
_ FC EIO DED __ __ __ No _____
with attached control units
_ 0E20 CTC 1 __________ ________________________________
_ 0E21 CTC 1 __________ ________________________________
_ 0E22 CTC 1 __________ ________________________________
_ 0E23 CTC 1 __________ ________________________________
with attached devices
-------Device------- --#--- --------Control Unit Numbers + --------
/ Number Type + CSS OS 1--- 2--- 3--- 4--- 5--- 6--- 7--- 8--- Base
_ 0E22 CTC 1 1 0E22 ____ ____ ____ ____ ____ ____ ____



-------Device------- --#--- --------Control Unit Numbers + --------
/ Number Type + CSS OS 1--- 2--- 3--- 4--- 5--- 6--- 7--- 8--- Base
_ 0E23 CTC 1 1 0E23 ____ ____ ____ ____ ____ ____ ____


If i try to define chpid FC on my other IODF I get the message
Essssssssssssssssssssssssssss Add Channel Path sssssssssssssssssssssssssssssN
e CBDPCH10 e
e e
e Specify or revise the following values. e
e e
e Processor ID . . . . : SYSPZ800 e
e Configuration mode . : LPAR e
e Channel Subsystem ID : e
e e
e Channel path ID . . . . FC + PCHID . . . ___ e
e Number of CHPIDs . . . . 1 e
e Channel path type . . . EIO + e
e Operation mode . . . . . DED + e
e Managed . . . . . . . . No (Yes or No) I/O Cluster ________ + e
e Description . . . . . . ________________________________ e
e e
e Specify the following values only if connected to a switch: e
e Dynamic entry switch ID __ + (00 - FF) e
e Entry switch ID . . . . __ + e
e Entry port . . . . . . . __ + e
e e
e e
DsssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssM
EsssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssN
e Channel path type EIO is not supported by channel path ID FC. e
DsssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssM


Is it possible to define the chpid with an other path type ?
louis@xtsoft.com [hercules-390]
2018-05-19 01:34:39 UTC
Permalink
Hi Brian
I thank you for the time you spent on my problem.
You are right E22-E23 are not defined in my IODF.
I have some difficulties to include these address in my IOCP.
Looking at the IODF of the Z/OS working well I can see


Chpid
FC EIO DED
With attached control units
_ 0E22 CTC 1 __________ _
_ 0E23 CTC 1 __________ _
With attached devices
-------Device------- --#--- --------Control Unit Numbers + --------
/ Number Type + CSS OS 1--- 2--- 3--- 4--- 5--- 6--- 7--- 8--- Base
_ 0E22 CTC 1 1 0E22 ____ ____ ____ ____ ____ ____ ____
_ 0E23 CTC 1 1 0E23 ____ ____ ____ ____ ____ ____ ____


When I try to define a chpid with type EIO i get the message
EsssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssN
e Channel path type EIO is not supported by channel path ID FC. e
DsssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssM


The chpid FC is new in this IODF.


Can I use an other type(not EIO) ?


Louis
louis@xtsoft.com [hercules-390]
2018-05-22 19:19:47 UTC
Permalink
Brian


I am really sorry. I did not want to upset you.
As my English is not very good, I thought I was not understood and explained my last message.
The time you spent on my problem was precious to me.




Louis

Loading...